Saws can be used in a woodworking shop, as a permanent instrument installed or used on the site as a portable or semi-portable. I sense the construction of the miter saw table, two types of plants. The purpose of a miter saw table is twofold: (1) to raise the saw up to a height comfortable working for the operator and (2) an area on the left side and / or right of the saw to consider enlarging the enclosure and support for long objects, providingcut. Have you ever tried a 45-degree miter cut at one end of a 2 x 6 x 12, you know, because they have a cutting table or roller is absolutely necessary.
Miter saws are often used to make repeated cuts of the same length. To stop any type of visa is practical and greatly accelerates the production time for this type of application. To stop a saw must be something to it, keeping fit in general to a fence. You can make your own fence by a very simple piece of wood or metal, or you canto do what I did and buy a parking available in mobile commerce, which slides along a rail of aluminum, which includes a stick tape.
TABLE SAW SHOP FOR PERMANENT
Since I buy wood in lengths up to 14 meters, I decided to build a miter saw long table in my woodworking shop. You may not have the physical space for them in your shop to have my measurements to be reduced accordingly. In the longer you build it, which is best for you, but any lengthThe saw bench is better than no table at all. My miter saw table measures 8 feet on the left side of the blade and another 8 feet on the right side of the blade. That way I can support the entire length of a sheet of plywood on both sides.
The table saw is built with 2 x 4 frame and contains a number of drawers under the table I use to store small tools and materials. If you want the room can be opened under the table or shelf space for the preservation of wood. Isuggest that the first 3 / 4 particle "Formica or melamine over 3 / 4". If the entire width of 4 feet melamine or particle board to using all means to do so, especially if the cutter such as "chop." With regard to the height of the general plan, I suggest you use the miter saw table build, so that the top of the table is standing at your waist. This gives you a comfortable working height, and yet you can lean on the table.
Sinceshould be a gap should, table saw is mounted in the area where the saw to cut. This shortcoming needs to be exactly as wide as the top of the saw and must be open to the front of the table. The gap should be seen behind the tip of his gun nearby. The saw should be placed in this gap, so that the tip of the miter saw table is flush with the top of the table saw. The handle must be free of guns, the entire route in both directions, moving from left to right.
Anticipating the needs of this gap, as you areFraming the bottom of the miter saw table, because you need to be built under a shelf, looked at the weight of the support Kapp. Maybe you want to do this in increments of micro-adjustable shelf, so you can get the saw platform exactly flush with the top of the table saw. You can do it with screws with washers delay through the cracks in the sliding shelf cabinet and table-frame. Loosen the delays and tap against the table top or bottom with a rubber malletTightening of the LAG in full. Use a ruler along in all directions to ensure that the saw and miter saw, the table is flush with the other. Mount the saw safely on the shelf with screws lag.
Once the miter saw is mounted, you can start building the fence or fences. A simple, inexpensive fencing is 4 x 6 or 1 x clear pine boards were in use before these cards should be hand selected for straightness and articulated on one side. A table is the current fence andothers consider it only from behind. The fence sits down with the edge of the hinged floor has seen, while the back-up board is flat on the table, behind the fence, in combination with the ragged edge on the bottom of the fence.
Before combining the two boards, in case of cracks in the back-up board for the purpose of installation and adjustment of the fence are being cut position on the table with reference to the fence on the miter saw. These slots should be slightly wider than the treeDiameter lag screws that you want to use to mount the fence on the table. Cut a couple of openings evenly distributed in the back-up board perpendicular (right angle) to the fence. X 2 4 beams must be placed at the center under the table, including the slots in the back-up board. In order for the lag screws to get a little 'harder to bite.
Before installation of the fence or fences around the table saw, draw a pencil or chalk line, where to be positioned in front of the fence. Take a longRuler, lay it flat on the miter saw is a metal table and miter saw scroll through long metal fence board. Remains in this position, draw a pencil along the table top, as far as possible. Repeat on the opposite side of the saw when you have tables on both sides of the blade. Extend the pencil line as far as possible.
Set the fence along the pencil line with the end of the wooden fence, miter saw, almost touching the end is a metal fence. (Leave a "gap 1 / 16 betweenWooden fence and wire mesh.) Drill holes of appropriate size for the wood screws through the table top and 2x4 beams under the table top (one for each slot). Tighten loose the fence on the table so that it can be set. Use the long straight side of the miter saw table and align the front of the fence, the fence and tighten fully. Repeat for the other side of the table if there is one.
For the fence on the left, instead of reading "right to left" stick-onTape along the top of the fence. For the fence on the right, instead of a reading "from left to right" stick-on tape along the top of the fence. Before gluing the strips must be perfectly aligned. The left wing is to measure the distance from the left side of the teeth of the saw blade and the right wing is to measure the distance from the right side of the teeth of the saw blade. With a simple wooden fence in this way, you can break the blocks of wood attached to the fence with C-clamps for repetitiveCuts.
An alternative bit 'more expensive and far better to stop the use of a trace metal or trace with a flip-up tape is made and built in. This device Tools Krege and is available in 4 foot lengths of track, you can join, are at greater length. My miter saw table, four 4-foot-tracks, two on each side of the saw. The track is located on the top of the wooden fence that you just installed. You need to adjust the height of the wooden fence (2 1 / 4 "and largerthe table above), so that the bottom clears the flip-up stop at the table about 1 / 16 "in the lowest position.
The beauty of the flip-up station that can be folded out of the way without losing their attitude measurement on the scale. If you were repetitive cuts and you no longer need to use the saw for a moment a different type of cut, you could cut repeated once more, without loss of accuracy.
TABLE PORTABLE MitreUSE site
Miter saw table is a construction site are usually attached with a saw at the bottom right of the table. I noticed that most of the miter saw to make their manufacturers metal table tops so that they are 3 1 / 2 "above the table on which rested the saw. A very simple, milled 4 x 4 (3 1 / 2" x 3 1 / 2 ") can be mounted on the table, near the plant on the left side of the table saw for metals. The 4 x 4 should be out for the entire length of the board support on the left andmounted on the table for support.
A fence can be attached to the back of 4 x 4. Use a 1 6 x 8 or 1 x clear pine board for this purpose. As mentioned in the table permanently, the ideal closure for the fence to the miter saw fence is made of metal. If a larger bearing surface is required, according to a fixed 4 x 4 in front of the fence to install. Krege Trak system with a flip-up stop can also be used on this portable table saw miter. Just make sure that theWooden fence is torn at the right height to stop the flip-up table to 1 / 16 clear. "(Fence is 2 1 / 4" + over the top of the 4 x 4).
As for the shelf, I used a plastic folding table from Costco. They come in different sizes to meet your specific needs. Or you can create tables and x 2 "plywood 4 3 / 4. Design, so that the legs fold for transport and storage.
|
Price : $133.00 |
Post Date : Sep 12, 2011 19:12:07
